Belling Rangehood Push Button Control Switch BL90B BL90S BL110B BL110S
BL series only - the BC series uses a different switch
SKU: SLN_2_0006086
Most of our items are in stock and will be dispatched within 3 working days.
In rare cases where an item needs to be sourced from our supplier, dispatch may take up to 7 working days.
Belling Rangehood Push Button Control Switch – BL Series Canopy Rangehoods
Genuine Belling push button control switch for the BL series CookCentre canopy rangehoods. This is the five-key switch bank behind the fascia – Stop, Low, Mid, High and Light – that runs the three fan speeds and switches both LED lamps. If one fan speed has stopped working, or the light will not switch while the fan still runs, this is almost always the part at fault rather than the motor or the lamp.
Belling rangehoods split into two families and the switches are catalogued as separate, non-interchangeable parts whose numbers are only two digits apart:
• BL series (BL90B, BL90S, BL110B) → this switch
• BC series (BC60B, BC60S, BC90B) → a different switch, part 17473000000098
Note the BC range includes a 90cm hood too, so searching on “90cm Belling” alone is not enough – check whether your model starts BL or BC.
BL110S: we believe this switch also suits the stainless 110cm hood, since it shares a manual and the same controls with the BL110B and the black/stainless finish does not change the part on the 90cm models. It is not separately listed in the parts catalogue, so if you have a BL110S please email us to confirm before ordering.
If your fan runs but the light is dead, note the LED lamp assembly is a separate part (17473000000136).
| Part number | 17473000000096 |
| Position on the BL90B parts diagram | Item 12 |
| Quantity supplied | 1 switch |
| NOT interchangeable with | 17473000000098 – the BC series switch (BC60B, BC60S, BC90B) |
| Related parts on these hoods | 17473000000136 LED light assembly · 12173000001200 charcoal filter |
| Supersession | None recorded |
Brands: Belling. These are the Belling CookCentre canopy rangehoods sold in Australia by Glen Dimplex. The black (B) and stainless (S) finishes use the same switch. If your model is not listed, send us your full model number and we will check it for you.
| One fan speed works, another does not | The contact set behind a single key has worn or burnt out. The classic sign that the switch has failed rather than the motor. |
| Light will not switch on while the fan still works | The lamp circuit runs through its own contact set inside the same switch body. |
| A button sticks down or will not release | The mechanical latch that pops the other keys back out has worn. |
| Fan changes speed or cuts out on its own | Degraded contacts making and breaking intermittently. |
| Burnt smell, buzzing, or browned contacts | Arcing across worn contacts. Stop using the hood and replace the switch. |
| The switch bank pushes back into the fascia | The retaining clips have fatigued and no longer hold it. |
| Grease and heat damage | This switch sits in the hot, greasy airstream directly above the cooktop, which is why it wears out well before the motor does. |
| Part type | Push button control switch bank |
| Keys | 5 – Stop, Low, Mid, High, Light |
| Controls | 3 fan speeds and the LED lamps |
| Hood electrical rating | 220-240V ~ 50/60Hz, 330W motor, 2 x 1.5W LED lamps |
| Quantity supplied | 1 |
| Condition | New, genuine |
| Note on dimensions | Belling do not publish dimensions or an electrical rating for this switch on its own. If you need exact measurements before ordering, contact us and we will measure one. |
| Isolate the power first | Switch off at the switchboard, or unplug the hood if it is on a plug lead, before any panel comes off. |
| This is licensed electrical work | In Australia, replacing a switch inside a hard-wired appliance must be done by a licensed electrician. Please do not attempt it otherwise. |
| Photograph the wiring before you disconnect it | A five-key motor and light switch has several terminals and there is no published wiring diagram for it. A photo on your phone is the only reliable reference when you put it back together. |
| Check the old switch against the photo | If your hood model starts with BC rather than BL, stop – you need the other switch. |
| Correct part, first time | Send us your model number and we will confirm fitment before you order. |
| Australia-wide delivery | Dispatched from our Sydney warehouse to all states and territories. |
| Appliance spares specialists | We supply trade technicians and DIY customers across Australia every day. |
| Questions before you buy | Email [email protected] and we will help you identify the right part. |
| AIRLINK | |
| SKU | SLN_2_0006086 |
| Model # | 17473000000096 |
| Brand | Belling |
| Shipping Weight | 1.0000kg |